日本三菱工程 卤素阻燃防火V0 PBT 5010GN2-30 含玻纤 电子应用详细介绍
![](https://res.gys.cn/img/mobile/common/loading/circle-loading.svg)
![](https://res.gys.cn/img/mobile/common/loading/circle-loading.svg)
![](https://res.gys.cn/img/mobile/common/loading/circle-loading.svg)
日本三菱 PBT 5010GN2-30 物性表
物理性能 | 额定值 | 单位制 | 测试方法 |
---|
密度 | 1.66 | g/cm? | ISO 1183 |
收缩率 |
|
|
|
垂直流动方向 : 2.00 mm | 1.1 | % |
|
流动方向 : 2.00 mm | 0.40 | % |
|
吸水率 (饱和, 23°C) | 0.070 | % |
|
机械性能 | 额定值 | 单位制 | 测试方法 |
---|
拉伸模量 | 11000 | MPa | ISO 527-2 |
拉伸应力 (断裂) | 135 | MPa | ISO 527-2 |
拉伸应变 (断裂) | 2.0 | % | ISO 527-2 |
弯曲模量 | 10500 | MPa | ISO 178 |
弯曲应力 | 210 | MPa | ISO 178 |
冲击性能 | 额定值 | 单位制 | 测试方法 |
---|
简支梁缺口冲击强度 (23°C) | 9.0 | kJ/m? | ISO 179 |
简支梁无缺口冲击强度 (23°C) | 45 | kJ/m? | ISO 179 |
热性能 | 额定值 | 单位制 | 测试方法 |
---|
热变形温度 |
|
|
|
0.45 MPa, 未退火 | > 220 | °C | ISO 75-2/B |
1.8 MPa, 未退火 | 208 | °C | ISO 75-2/A |
熔融温度 | 224 | °C | ISO 11357-3 |
线形热膨胀系数 |
|
| ISO 11359-2 |
流动 : -30 到 50°C | 2.0E-5 | cm/cm/°C | ISO 11359-2 |
流动 : -30 到 120°C | 2.0E-5 | cm/cm/°C | ISO 11359-2 |
流动 : 50 到 120°C | 1.0E-5 | cm/cm/°C | ISO 11359-2 |
横向 : -30 到 50°C | 8.0E-5 | cm/cm/°C | ISO 11359-2 |
横向 : -30 到 120°C | 1.1E-4 | cm/cm/°C | ISO 11359-2 |
横向 : 50 到 120°C | 1.4E-4 | cm/cm/°C | ISO 11359-2 |
![](https://res.gys.cn/img/mobile/common/loading/circle-loading.svg)
![](https://res.gys.cn/img/mobile/common/loading/circle-loading.svg)
![](https://res.gys.cn/img/mobile/common/loading/circle-loading.svg)
![](https://res.gys.cn/img/mobile/common/loading/circle-loading.svg)
![](https://res.gys.cn/img/mobile/common/loading/circle-loading.svg)
![](https://res.gys.cn/img/mobile/common/loading/circle-loading.svg)
![](https://res.gys.cn/img/mobile/common/loading/circle-loading.svg)
![](https://res.gys.cn/img/mobile/common/loading/circle-loading.svg)
PBT又可称为热塑性聚酯塑料,为适用于不同加工业者使用,一般多少会加入添加剂,或与其它塑料掺混,随着添加物比例不同,可制造不同规格的产品。由于PBT具有耐热性、耐候性、耐药品性、电气特性佳、吸水性小、光泽良好,广泛应用于电子电器、汽车零件、机械、家用品等,而PBT产品又与PPE、PC、POM、PA等共称为五大泛用工程塑料。
PBT 结晶速度快,***加工方法为注塑,其他方法还有挤出、吹塑、涂覆和各种二次加工成型,成型前需预干燥,水分含量要降至0.02%。
缺点是缺口冲击强度低 ,成型收缩率大 。故大部分采用玻璃纤维增强或无机填充改性,其拉伸强度、弯曲强度可提高一倍以上,热变形温度也大幅提高。可以在140℃下长期工作,玻纤增强后制品纵、横向收缩率不一致,易使制品发生翘曲。
PBT 结晶速度快,***加工方法为注塑,其他方法还有挤出、吹塑、涂覆和各种二次加工成型,成型前需预干燥,水分含量要降至0.02%。
因篇幅有限,关于物性表的更多详情不能一一展示在这,了解更多信息或是报价请马上拔打东莞伟才塑胶原料公司电话,期待用我们的专业为你创造价值!